Page Programming Toggle Option Sections Programming Toggle Option Sections The keypad displays the information using a binary format, according to the following chart: See Hex data Some programming sections contain several toggle options. Delay 1 in programming section [] System Times. Page Communicator - Account Numbers There are two account numbers pro- When an alarm occurs while the panel is armed and a second grammable for the PC Section [] period, or after the system is disarmed, this code will be sent.
Page Test Transmission 5. Page 34 [] Keypad Zone Assignments Section 2. All others will be ignored. PGM Options are programmed in []. Page 38 [] Priority Alarm and Restoral Section 5. All LCD programming is done per key- pad. If more than one LCD keypad are present on the system, labels programmed at one keypad can be broadcast to all other LCD keypads. These are described below.
Record all your program- ming choices in the programming worksheets included in this manual. Programming Keypad Options Programming the LCDZ is similar to programming the rest pad displays the time with options [1] to [3] in programming sec- of the system. Page 55 Notes Page 3: Features Using the Big Books Features are the options that you need to Features programme in order to have the features work appropriately.
Now look at page Page 4: Installation 3. Connect the mains cable to the unswitched fuse spur and to the control panel. Page 5 Section 1 is the basic overview of the and communications if pro- panel specifications including AUX, grammed. Bell and PGM output current ratings, battery and transformer requirements and a quick description of some of the more common features.
The Keybus is a simple 4- zone is activated. Page 9: Wiring Fire Detectors Press [2] and the dash is detectors should be connected to the replaced by the number, indicating Classic PC control panel. Page Wiring Sab If you want to exit strobe connection. Page Telephones If [1] comes ON, push [1] again for specific trouble present. Check telephone line, telephone number of Central Initial Start Up Station, format and reporting Before turning on the mains power, codes.
Dial number from handset and listen for tones to ensure make sure that all electrical connec- tions are completed and all devices Smoke detectors may not detect smokefrom fires on another level of the residence or building. Every fire is different in the amount of smoke produced and the rate ofburning. Smoke detectors cannot sense all types of fires equally well.
Smokedetectors may not provide timely warning of fires caused by carelessnessor safety hazards such as smoking in bed, violent explosions, escaping gas,improper storage of flammable materials, overloaded electrical circuits, chil-dren playing with matches or arson.
Even if the smoke detector operates as intended, there may be circumstanceswhen there is insufficient warning to allow all occupants to escape in time toavoid injury or death. Motion DetectorsMotion detectors can only detect motion within the designated areas asshown in their respective installation instructions. They cannot discrimi-nate between intruders and intended occupants.
Motion detectors do notprovide volumetric area protection. They have multiple beams of detec-tion and motion can only be detected in unobstructed areas covered bythese beams. They cannot detect motion which occurs behind walls, ceil-ings, floor, closed doors, glass partitions, glass doors or windows.
Anytype of tampering whether intentional or unintentional such as masking,painting, or spraying of any material on the lenses, mirrors, windows orany other part of the detection system will impair its proper operation. Passive infrared motion detectors operate by sensing changes in tempera-ture. However their effectiveness can be reduced when the ambient tem-perature rises near or above body temperature or if there are intentional orunintentional sources of heat in or near the detection area. Some of theseheat sources could be heaters, radiators, stoves, barbeques, fireplaces, sun-light, steam vents, lighting and so on.
Warning DevicesWarning devices such as sirens, bells, horns, or strobes may not warnpeople or waken someone sleeping if there is an intervening wall or door. If warning devices are located on a different level of the residence orpremise, then it is less likely that the occupants will be alerted or awak-ened. Audible warning devices may be interfered with by other noisesources such as stereos, radios, televisions, air conditioners or other ap-pliances, or passing traffic.
Audible warning devices, however loud, maynot be heard by a hearing-impaired person. Telephone LinesIf telephone lines are used to transmit alarms, they may be out of service or busyfor certain periods of time.
Also an intruder may cut the telephone line or defeatits operation by more sophisticated means which may be difficult to detect. Insufficient TimeThere may be circumstances when the system will operate as intended, yet theoccupants will not be protected from the emergency due to their inability torespond to the warnings in a timely manner.
If the system is monitored, theresponse may not occur in time to protect the occupants or their belongings. Component FailureAlthough every effort has been made to make this system as reliable as possible,the system may fail to function as intended due to the failure of a component. Inadequate TestingMost problems that would prevent an alarm system from operating as in-tended can be found by regular testing and maintenance.
The complete sys-tem should be tested weekly and immediately after a break-in, an attemptedbreak-in, a fire, a storm, an earthquake, an accident, or any kind of con-struction activity inside or outside the premises. The testing should includeall sensing devices, keypads, consoles, alarm indicating devices and anyother operational devices that are part of the system.
0コメント