Before operating the washer, remove the bolts along with the rubber bungs. Unscrew the 3 bolts with the spanner supplied, and take out the 3 bolts with the rubber bungs. Keep the 3 bolts and the spanner for future use.
Must be with 1. Do not overload the outlet with more than one appliance. For wall, door and floor modeling is required. As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:. The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured Green or Green and Yellow.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or. In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the cold water inlet valve.
Option : Be careful not to confuse hot water inlet and cold water inlet. This will cause abnormal noise. The level adjustment of the washing machine prevents excessive noise and vibration. Install the washing machine on a solid and even floor surface, if possible, in a corner of the room. Note: the wooden floor may cause excessive vibration. If the floor is uneven, adjust the adjustable leg as the following.
When pushing down the edges of the washing machine top plate diagonally, the machine should not move up and down at all. If machine rocks when pushing the machine top plate diagonally, adjust legs again. Before cleaning the washer interior, unplug the electrical power cord avoid electrical shock hazards.
The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent.
Immediately wipe off any spills. Wipe with damp cloth. If the washer is stored in an area where freezing may occur or moved in freezing temperature, follow these instructions to prevent damage to the washer.
Turn off water supply tap. Disconnect hoses from water supply and drain water from hoses. Plug electrical cord into a properly grounded electrical outlet. Add 1gallon 3. Close the door. Set spin cycle and let washer spin for 1minute to drain out all water. Unplug eletrical power cord, dry the drum interior, and close the door. Remove detergent case and dry excessive water from the compartments. Store washer in an upright position. Pllease, check both of two directions If machine rocks when pushing the machine top plate diagonally, adjust legs again.
Exterior Proper care of your washer can extend its life. The outside of the machine can be cleaned with warm water and a neutral non abrasive houshold detergent. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with sharp objects. Interior Dry around the washer door opening, flexible gasket and door glass. Run washer through a complete cycle using hot water.
Repeat process if necessary. Turn off water supply tap. Disconnect hoses from water supply and drain water from hoses. Plug electrical cord into a properly grounded electrical outlet. Add 1gallon 3. Close the door. Set spin cycle and let washer spin for 1minute to drain out all water. Unplug eletrical power cord, dry the drum interior, and close the door. Remove detergent case and dry excessive water from the compartments. Store washer in an upright position. To remove antifreeze from washer after storage, run empty washer through a complete cycle using detergent.
Do not add wash load. Turn off the water tap. Unscrew the water inlet hose. Clean the filter using a had bristle brush. Tighten up the inlet hose. Open the lower cover 1 by using a coin. Turn the cap hose 2 to pull out the hose. Pull out the hose maximally. Remove any foreign material 2. Unplug the cap hose 2 , allowing the water to flow out. At this time use from the pump filter 3.
After a vessel to prevent water flowing on cleaning, turn the pump filter to the floor. When water does not clockwise and insert the cap flow any more, turn the pump hose 2 to the original place. Close the lower cover. When you want to change program in operating, press this button. Temperature Button This button can be used to adjust temperature of water according to types of the load to be washed.
Spin Speed Button By pressing this button, the spin speed can be chosen. No Spin If no spin is selected, the washer stops after draining water. Rinse Hold This function leaves clothes in the machine suspended in the water after a rinse without entering into spin. Option Button By pressing this button, all option functions may be selected.
Pre-Wash If the laundry is heavily soiled, Pre-Wash course is effective. Pre-Wash is available in Cotton and Synthetic. Crease Care If you want to prevent crease, select this button with spin speed. Time save is available in Cotton, Eco and Synthetic. Time Delay Button If you want to reserve the finishing time of washing, use this button. If the Time Delay button is pressed, "" is displayed. The maximum delayed time is hours and the minimum time is hours.
Each pressing of the button advances on time delay by one hour. Child Lock Button If you want to protect any accident occuring from handling of washer by a child, use this function. To change to the desired program, while in child lock mode. Press both "Time Save" and "Time Delay" buttons together once again. If an unbalanced load is detected of if suds removing program operates, the washing time maybe extended.
Maximum increasing time is about 1hour. At this time, the version is displayed on the Custom LED 3 Each load makes a movement as follows, whenever the Time Delay button is pressed a time. When the machine does not function properly or does not fuction at all, check the following points.
The washing label of your garment shows the recommended washing temperature. Do I need to use an anti-scaling agent for my washing machine? It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash. How do I prevent my washing machine from smelling? Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.
0コメント